Yahoo! Japan Site General Tag Setup Guide

Tag tips

• IMPORTANT: To trigger a particular tag, set up the trigger condition in the Tag Types tab in the mapping toolbox. Otherwise, no tags will be triggered.
• Use mappings to override the standard configurations.
• You may enter more than one ID or Label in a comma-separated list. If you enter one ID and multiple Labels, you will trigger one call for each Label, each using the same ID. If you enter multiple IDs and a single Label, you will trigger a call for each ID, each using the same Label. If you enter multiple IDs and Labels for a single tag type, make certain the numbers of IDs and Labels match.
• Supports these E-Commerce extension values:
  • Order ID (_corder)
  • Order Subtotal (_csubtotal)
  • List of Product IDs (_cprod)
  • List of Product Categories (_ccat)
  • List of Product Quantities (_cquan)
  • List of Product Prices (_cprice)

Tag configuration

Navigate to the Tag Marketplace to add a new tag. Read the Tag Overview article for general instructions on how to add a tag.

When adding the tag, configure the following settings:

• Auto Tagging: Enable or disable auto tagging. Enabling this setting performs the ytag({"type":"ycl_cookie"}); call after the tag loads.
• Display Network Conversion IO: Enter your Yahoo! Japan Display Network (YDN) Conversion IO.
• Display Network Conversion Label: Enter your Yahoo! Japan Display Network (YDN) Conversion Label.
• Display Network Retargeting ID: Enter your Yahoo! Japan Display Network (YDN) Retargeting ID.
• Display Network Retargeting Label: Enter your Yahoo! Japan Display Network (YDN) Retargeting Label.
• Sponsored Search Conversion ID: Enter your Yahoo! Japan Sponsored Search (YSS) Conversion ID.
• Sponsored Search Conversion Label: Enter your Yahoo! Japan Sponsored Search (YSS) Conversion Label.
• Sponsored Search Retargeting ID: Enter your Yahoo! Japan Sponsored Search (YSS) Retargeting ID.

Data mappings

Mapping is the process of sending data from a data layer variable to the corresponding destination variable of the vendor tag. For instructions on how to map a variable to a tag destination, see data mappings.

To fire any tags, you must set up the trigger condition in the Tag Type category.

The available categories are:

Display Network (YDN) Conversion

Display Network (YDN) Retargeting

Sponsored Search (YSS) Conversion

Sponsored Search (YSS) Retargeting

E-Commerce

Tag Types

Type-Specific Parameters

Use cases

Trigger YDN Retargeting on every page that matches load rules

To set up a tag which fires on every page according to load rules:

1. On the Tag Configuration tab, enter the appropriate value for the Display Network Retargeting ID box.
2. Set Auto Tagging to True. This will trigger the ytag({"type":"ycl_cookie"}); call.
3. Set up your load rules as needed.
4. On the Data Mappings tab in the Variables dropdown, click Use Custom Value.
5. In the upper-left section of the dialog, enter true in the box.
6. In the Category section, select Tag Types.
7. In the When mapped variables equals box, enter true.
8. In the Trigger tag type dropdown, select Display Network Retargeting.
9. Click +Add.
10. Click Done.
11. Click Apply.

Trigger YDB Conversion on a purchase event while retargeting on other pages

To set up a YDN Conversion tag which fires on a page with a tealium_event variable value of purchase and a Retargeting tag on every other page according to load rules:

1. Set up your Retargeting tag as described in the Trigger YDN Retargeting on every page that matches load rules section above.
2. On the Tag Configuration tab, enter the appropriate values for the Display Network Conversion IO and Conversion Label boxes.
3. On the Data Mappings tab in the Variables dropdown, select tealium_event.
4. Click +Select Destination.
5. In the Category section, select Tag Types.
6. In the When mapped variables equals box, enter purchase.
7. In the Trigger tag type dropdown, select Display Network Conversion.
8. Click +Add.
9. Repeat steps 3 through 8 for similar mappings, such as Conversion Transaction ID and Conversion Value, by Selecting Display Network (YDN) Conversion from the Category section.
10. To fire the conversion on multiple pages, either repeat these steps or create a vendor-specific variable (for example: yahoo_conversion_value), which can be dynamically assigned via extensions.
11. Click Done.
12. Click Apply.

Trigger YDB Conversion on a specific page’s URL while retargeting on other pages

To set up a YDN Conversion tag which fires on a specific page’s URL (for example: /cart/thankyou) and a Retargeting tag on every other page according to load rules:

1. Set up your Retargeting tag as described in the Trigger YDN Retargeting on every page that matches load rules section above.
2. On the Tag Configuration tab, enter the appropriate values for the Display Network Conversion IO and Conversion Label boxes.
3. On the Data Mappings tab in the Variables dropdown, select Custom Value.
4. Click +Select Destination.
5. In the Category section, select Tag Types.
6. In the When mapped variables equals box, enter the path to the page where your version should be triggered (for example: /cart/thankyou).
7. In the Trigger tag type dropdown, select Display Network Conversion.
8. Click +Add.
9. Repeat steps 3 through 8 for similar mappings, such as Conversion Transaction ID and Conversion Value, by Selecting Display Network (YDN) Conversion from the Category section.
10. To fire the conversion on multiple pages, either repeat these steps or create a vendor-specific variable (for example: yahoo_conversion_value), which can be dynamically assigned via extensions.
11. Click Done.
12. Click Apply.